Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 9 - Jul 14
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
tesa 40371 TPE Hygienic Replacement Made Toilet Brush Sets-Chrome-Plated Metal Handle-Dark Grey-37.4 x 7.1 x 7.4 cm, AnthraciteFeatures Top cleaning performance: From the flush passage to under the rim, this thermoplastic elastomer (TPE) toilet brush offers a greater cleaning power than conventional polyethylene toilet brushes Maximum hygiene: Equipped with 2 different types of bristles, the self cleaning toilet brush head has long bristles for hard to reach places and short bristles to tackle stubborn dirt Durable but gentle: The high quality silicone brush gently cleans
Features
- Top cleaning performance: From the flush passage to under the rim, this thermoplastic elastomer (TPE) toilet brush offers a greater cleaning power than conventional polyethylene toilet brushes
- Maximum hygiene: Equipped with 2 different types of bristles, the self-cleaning toilet brush head has long bristles for hard-to-reach places and short bristles to tackle stubborn dirt
- Durable but gentle: The high-quality silicone brush gently cleans toilets without leaving a scratch - It also retains its shape whilst being particularly long-lasting
- Sustainable and low in pollutants: As opposed to PVC, thermoplastic elastomer is an environmentally friendly material - No plasticisers used
- Match and mix: The toilet brush can be used with all tesa toilet brush sets - Simply reuse the brush handle with tesa disposable toilet brush heads
Product Description
A spotless bathroom is a must in every household. Feel comfortable in your home by adding this high-quality toilet brush to your WC set. The flexible bristles let you thoroughly clean ceramic toilets without damaging them. For a cleaner toilet, make downward movements to dislodge dirt. Upward movements remove grime over a wide area or further loosen it. There is also no need to worry about toilet muck or paper getting caught in the bristles. Practical and hygienic: the brush head cleans itself with the water flush. The replaceable brush head has a thread diameter of 3/8" (approx. 15mm). The handle is made with glossy chrome-plated metal. tesa - more than just an adhesive tape tesa stands for innovative, high-quality products and is one of the world's leading manufacturers of adhesive tapes and system solutions. For more than 125 years, the German company has been developing solutions for offices, homes, and gardens, as well as for the automotive and electronics industries. tesa offers private households several hundred innovative solutions for fastening, packaging, assembly, renovation, repair, insulation, and protection against insects, dust, and draughts.Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.2 ★★★★★
Based on 683 reviews
Sort
Product Reviews
★★★★★ 5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024
recommand products
H&R Coilover Kit | B6 | B7 Audi S4
741.00
H&R Springs - Sport Springs - 1in Front Lowering; 1in Rear Lowering
242.17
TESSAN Universal Travel Adapter Worldwide, Built in 35 W USB C Cable, International Travel Adapter with 4 USB Charging Ports, Universal Plug for UK to
63.39
H&R Coilovers | BMW E46 Xi
785.00
Optimum Energy Saving Electronic Time Switch - 2 Hour Electronic Boost Timer Socket Box Mount - White, One 230 V
32.88