Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 14 - Jul 19
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
RFX Pro Wheel Spacers Rear (Red) - Suzuki RM125/250Pro Series Wheel Spacers RFX Pro Series wheel spacers are lighter and more durable than OEM. Constructed from 7075 T6 aluminium and colour anodised to increase durability. This helps to reduce surface wear and lessens the amount of dirt entering the hub which in turn extends the life of the bearing. Designed with a rear lip to help keep them hooked into the seals, this reduces the chance of falling out during maintenance, speeding up wheel changes.
Pro Series Wheel Spacers
RFX Pro Series wheel spacers are lighter and more durable than OEM.
Constructed from 7075-T6 aluminium and colour anodised to increase durability. This helps to reduce surface wear and lessens the amount of dirt entering the hub which in turn extends the life of the bearing.
Designed with a rear lip to help keep them hooked into the seals, this reduces the chance of falling out during maintenance, speeding up wheel changes.
RFX products are tested and used by many top Grand Prix and British Motocross teams.
- 7075-T6 Aluminium Construction.
- Colour anodised for durability.
- Machined rear location lip.
Tag Line
CNC Machined
For a tighter tolerance
Fitting Instructions
- Start with the motorcycle on a box stand with the wheels raised from the ground.
- Remove the large spindle nut and loosen any pinch bolts on the lower fork leg.
- Remove the spindle from the wheel this may require the use of a brass punch and hammer if tight.
- Front wheel will now remove.
- The rear wheel should now be loose enough to push forward and lift the chain from the rear sprocket.
- Rear wheel will now remove.
- Remove the wheel spacers from the wheels.
- Clean in and around the seals with contact cleaner such as Maxima Electrical Contact and re-grease under the seal.
- Fit the new wheel spacers.
- Make sure to open the brake pads apart inside the brake callipers to give you extra room when re-fitting the wheel.
- Re-fit the wheels and push the spindles through.
- Re-fit the chain and set the proper chain tension by adjusting the axle blocks.
- Tighten
the large spindle nuts to the correct torque setting. - With the bike of the stand pump the front forks up and down to align the front forks then tighten the pinch bolts.
- Finally pump the brakes to re- align the callipers.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.5 ★★★★★
Based on 2331 reviews
Sort
Product Reviews
★★★★★ 5
Good quality
Model: 500N STD
This printer is the best is good quality i love it
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 27, 2025
★★★★★ 4
Good Prints for Sublimation
Model: 500N STD, Model: 500N STD
After years of using converted printers for sublimation, I finally decided to go with the Sawgrass printer, which is specifically designed for sublimation. The printer turned out to be very nice! I’m particularly happy about the Sawgrass customer service they provide.
Follow-up. I ordered the SG500 printer bundle from Amazon, but unfortunately, the prints had visible grid lines. I promptly reached out to Sawgrass customer service, and after a few emails, they figured out that the printer I received was faulty. It was all resolved within a few hours, which was way faster than I had expected. They immediately sent me a replacement machine and the prints are absolutely beautiful for my sublimation projects. Sawgrass customer service is truly amazing!
Over the past three months, I have been using the Sawgrass printer and have identified a shortcoming that I would like to share in my review. While the prints produced by the Sawgrass printer are satisfactory, they fall short of the quality achieved with a printer I previously used for several years. This printer required a conversion to sublimation printing.
I have sent a note to Sawgrass inquiring about potential solutions to this issue a couple of months ago, but I have not yet received a response. This suggests that the company may not have a viable remedy.
You be the judge. I followed Sawgrass recommendations and used the Sawgrass Print Utility, but no matter what changes I make, the converted printer seems to produce prints much more to my liking. Both of the book markers shown were sublimated at the same time.
In the future, when I have an order to complete, I will be opting to use the more affordable printer that I converted.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
★★★★★ 5
Sawgrass quality is excellent
Model: 500N STD, Model: 500N STD
I've been on the fence with Sawgrass, simply because cost can be an issue, but this past week I decided to put the new Sawgrass to the test against another of my printers which I converted for dye sublimation. I also own the Versiflex. I was on the fence with it initially as well, but I've been using it ALOT and I now have it down to an art. I've made shirts for friends and they were literally blown away at the quality of the print, so. . . yes, it is expensive and yes, you get what you pay for. So. . . I recently received the sublijet ink with my new Sawgrass since you cannot mix inks in a Sawgrass, not even to switch the type of ink for risk of damaging the machine. I'm seriously impressed. I made lanyards, T-shirts, bags and the quality is outstanding. I don't know if I'm going to retire my Epson, but the software to print using the Sawgrass print manager is pretty slick. Lots of options to fine tune your print quality. If you have the cash, buy it. If you don't save up. It's worth it. . . and this is coming from a skeptic.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on July 22, 2025
★★★★★ 5
Sawgrass is Always Innovating & Improving!
Model: 500N STD
I do own a versiflex and already have an expectation of quality and it did not let down. I’ve been running it for a few weeks and I’m honestly proud of what I’ve made. Mugs come out with deep blacks and smooth gradients, coasters are sharp edge to edge, and my poly tees keep their color after the first wash. Setup was fairly simple - drivers, print Manager, paper in, Wi-Fi paired first try. I barely tweak settings; reds, skin tones, and fine text land right without a lot of tinkering. No banding, no weird shifts, and the first print of the day is clean as it has an auto maintenance. For consistent, sellable results, it’s been worth it so far and I highly recommend it.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 11, 2025
★★★★★ 5
If you have a Cricut you need this
Style: Starter Bundle
Just what I needed to compliment my Cricut system. Works great, colors are perfect, set up was a breeze, connected to my wireless instantly. Prints look prefect, not all wonky like some can. Value pack was definitely worth the extra $50.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 21, 2026