Pay in installments of $112.38 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 19 - Jul 24
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Rear Main Crankshaft Oil Seal With Housing Fiat Palio Stilo Strada Multipla 1.6 MAP-100497Vehicle Compatibility Fiat Multipla 1. 6 Activ 182B6. 000 Petrol 2004 to 2009 Fiat Palio 1. 6 EL EH 178B3. 000 Petrol 2000 to 2005 Fiat Palio II 1. 6 178B3. 000 Petrol 2005 to 2008 Fiat Stilo 1. 6i Multi Wagon 182B6. 000 Petrol 2003 to 2007 Fiat Strada 1. 6 EL 178D2. 011 Petrol 2005 to 2010 This rear main crankshaft oil seal with housing is intended for the Fiat 1. 6 petrol engines listed above. It mounts at the rear of the crankshaft and should
Vehicle Compatibility
- Fiat Multipla 1.6 Activ 182B6.000 Petrol 2004 to 2009
- Fiat Palio 1.6 EL/EH 178B3.000 Petrol 2000 to 2005
- Fiat Palio II 1.6 178B3.000 Petrol 2005 to 2008
- Fiat Stilo 1.6i Multi Wagon 182B6.000 Petrol 2003 to 2007
- Fiat Strada 1.6 EL 178D2.011 Petrol 2005 to 2010
This rear main crankshaft oil seal with housing is intended for the Fiat 1.6 petrol engines listed above. It mounts at the rear of the crankshaft and should always be matched to engine code, gearbox layout and housing design before ordering, especially on South African vehicles where running changes are common.
Specifications
- Part type: Rear main crankshaft oil seal with housing
- SKU: MAP-100497
- Fitting position: Rear of crankshaft (gearbox side)
- Design: Seal pre-fitted in aluminium housing for easier replacement
- Nominal size: 64 x 180 x 20 mm
- Primary engine applications: Fiat 1.6 petrol engines 178B3.000, 182B6.000, 178D2.011 (and related 1.6 16V variants used in Palio, Stilo, Multipla and Strada)
- Vehicle families: Fiat Palio, Palio II, Strada, Multipla, Stilo 1.6 as listed in the compatibility section
- Application note: Only suitable where the removed rear seal and housing match the size and bolt pattern of this unit.
All dimensions and applications are based on catalog data for the specified Fiat 1.6 engines. Always compare the old rear seal housing and gasket pattern to this unit before opening packaging or attempting installation.
Features
- Complete rear main crankshaft oil seal supplied with housing to simplify replacement on Fiat 1.6 engines.
- Sized to suit common 1.6 applications in Palio, Palio II, Strada, Multipla and Stilo used in the South African market.
- Housing design allows for correct alignment and seating of the seal on the crankshaft flange when installed with the proper tools.
- Helps restore reliable oil sealing at the rear of the engine when used as part of a professional clutch or engine overhaul.
- Suitable for workshops and engine rebuilders that regularly service Fiat 1.6 petrol models.
Trusted by thousands of South African drivers for quality and durability when installed correctly and combined with proper maintenance.
Why Buy From Us
- Local South African stock of key engine sealing components for popular Fiat 1.6 models.
- 12 month warranty on this rear main crankshaft seal with housing, subject to correct installation and normal operating conditions.
- We assist with catalog checks – send us your VIN, engine code and any OE numbers so we can confirm compatibility before you place an order.
- Experience with the Fiat Palio, Stilo, Multipla and Strada ranges commonly found on South African roads.
- Nationwide delivery across South Africa, including Cape Town, Johannesburg, Pretoria, Durban, Gqeberha and many other areas.
Installation & Maintenance Tips
- Have the rear main crankshaft oil seal and housing fitted by a qualified technician or engine rebuilder.
- Remove the gearbox and clutch assembly as required to gain full access to the rear of the engine before attempting to replace the seal.
- Before removing the old housing, note its position and depth in relation to the engine block and sump; reproduce this with the new unit.
- Thoroughly clean the crankshaft flange, sealing surface and engine block mounting face, removing any old gasket material and sealant.
- Inspect the crank flange for grooves or damage; excessive wear may require repair or specialist attention before fitting the new seal.
- Use the correct alignment tools or dowels to position the housing squarely so the seal lip runs true on the crankshaft.
- Apply a light film of clean engine oil to the seal lip if recommended by the manufacturer and tighten all housing bolts to the specified torque.
- After reassembly, check for oil leaks and confirm that crankcase ventilation is operating correctly to prevent pressure build-up behind the seal.
These notes are general guidelines only and do not replace the official Fiat workshop procedures for your specific engine and model.
Engine Parts Installation Warning
Internal engine components such as rear crankshaft seals and housings must only be installed by suitably qualified technicians with the correct tools, measuring equipment and technical data. Incorrect alignment, damage to the seal during installation, contaminated mating surfaces or failure to follow the manufacturer’s procedures can lead to serious oil leaks and potential clutch or engine damage.
Before installation, verify engine code and application, compare the new housing and seal to the original unit and ensure all related components are in good condition. The installer is responsible for following the torque values and assembly instructions specified by the vehicle manufacturer.
Engine Parts Return Policy Warning
For internal engine parts and sealing components, returns are strictly controlled for safety and quality reasons. Once the packaging has been opened or the component shows signs of handling, fitting, oil contamination or workshop marks, it is generally considered non-returnable.
Returns will only be considered where an incorrect item was supplied and the part is still unused, clean and in its original, undamaged packaging with all labels intact. Always check engine code, housing design, bolt pattern and key dimensions of the old unit against the new one before opening sealed packaging or attempting installation. Please refer to our full refund and returns policy for the detailed conditions that apply in South Africa.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy